Psycho Paint
Psycho Paint is a versatile and easy to use platinum silicone paint base developed to help special effects and prosthetic artisans, doll makers, etc. easily create painted-on color effects for their platinum silicone creations. It is a two component translucent clear platinum-cure silicone that is used to make a base for color pigmenting. Once the desired color is attained, Psycho Paint is thinned with a solvent. Thin layers of paint can be then be applied to a model's surface (made of Dragon Skin , Ecoflex or other platinum silicone) using an airbrush.
In addition to painting the exterior of a cast piece, you can apply Psycho Paint to the inside of a platinum silicone or urethane rubber mold and then cast platinum silicone behind it. It can also be applied by brushing.
Technical bulletin Psycho Paint
Psycho Paint
Psycho Paint_
Which pigments to use?
On the next tab's you will find pigments that can be used with Psycho Paint
Instructions
Safety - Use in a properly ventilated area ("room size ventilation). Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Wear vinyl gloves only. Latex gloves will inhibit the cure of the rubber.
Store and use all products at room temperature (73 F / 23 C). This product has a limited shelf life and should be used as soon as possible. Silicone surfaces to be painted can only be Platinum (addition) cured systems. For optimum results the silicone skin/surface, should be painted as soon as possible after demolding. We recommend that the cured piece to be painted be no more than 2 days old.
Clean All Surfaces That Will Contact Psycho Paint - All surfaces to be painted, need to be free of any contaminants (especially mold release). If necessary, clean all surfaces with solvent (NOVOCS Zero VOC Solvent, Toluene, Xylene, or Naptha), and allow to dry before painting.
Measuring Is Done By Volume - The recommended mix ratio is 100 Parts A + 100 Part B + 200-500 Parts Solvent depending on your application (hand painting vs. airbrushing).
Adding Color To Psycho Paint - Silc Pig silicone pigments are compatible with Psycho Paint . There are several colors to choose from, and you can mix colors to create custom colors. The most accurate way to add pigment is by weight (using a gram scale). We recommend beginning by pre-mixing 2% pigment by weight to Part B and pre-mixing thoroughly. Do not exceed a 5% pigment load of the total weight (A+B). You can also use powdered cosmetic pigments to color Psycho Paint , however a compatibility test is recommended.
Adding Solvent - Once a desirable color effect is attained, add an equal amount of Psycho Paint Part A. Next, add 200-500 Parts of solvent. Smooth-On"s NOVOCS Zero VOC Solvent is recommended. Toluene, Xylene or Naptha are also suitable. Observe all safety precautions when handling combustible or flammable solvents. Mix thoroughly to a uniform color (no streaks).
Applying Psycho Paint Using An Air Brush - Dispense mixture into air brush siphon cup / gravity cup. Apply thin layers of paint to the model"s surface until the desired color effect is attained.
Brushing Onto A Platinum Silicone Appliance Or Model - Make sure all surfaces are clean. Add the desired amount of Silc Pig pigment to Psycho Paint Part B and mix thoroughly. Add an equal amount of Psycho Paint part A and mix thoroughly. Add solvent if desired. You can then apply Psycho Paint with a brush. A common application technique is to use a "stippling effect.
Important - Pot life of undiluted Psycho Paint (without solvent) is 20 minutes at room temperature.
Curing - Undiluted Psycho Paint will cure at room temperature in 2 hours. Cure time can be reduced with heat (oven or heat gun). Do not expose to over 212 F/100 C. If heat curing, make sure that all solvents have evaporated from model"s surface, before applying heat.